جميع الحقوق محفوظة لهيئة لتقييس لدول مجلس التعاون لدول الخليج العربية.
ما لم ينص على خلاف ذلك، لا يجوز إعادة إنتاج أي جزء من هذا المنشور أو استخدامه بأي شكل آخر أو بأي وسيلة، إلكترونية أو ميكانيكية، بما في ذلك التصوير، أو النشر على الإنترنت أو الإنترانت، دون إذن كتابي مسبق من هيئة التقييس لدول مجلس التعاون لدول الخليج العربية على العنوان أدناه أو الدول الأعضاء في الهيئة داخل بلدانهم.
All rights reserved to GCC Standardization Organization (GSO). Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either GSO at the address below or GSO's member body in the country of the requester.
Outreach Dept, Knowledge Management Section
GCC Standardization Organization (GSO)
P.O.Box: 85245 Riyadh 12511
Kingdom of Saudi Arabia
إدارة التواصل، قسم إدارة المعرفة
هيئة التقييس لدول مجلس التعاون لدول الخليج العربية (GSO)
GCC Standardization Organization (GSO) is a regional organization which consists of the national standardization bodies of GCC member states. One of GSO main functions is to issue Gulf Standards and Technical Regulations through specialized technical committees.
GSO Board of Directors
in its meeting number (10) held
on 16/04/1409 H,
which corresponds to 26/11/1988, has approved
the translation of
the document
GSO 98:1988
as a Gulf
Technical Regulation
titled "MOTOR VEHICLES- FLAMMABILITY OF
INTERIOR MATERIALS AND THEIR
TESTING METHODS
" in
English
language
which was studied
through
the technical program of
GSO Technical Committee for Mechanical Products
(TC02)
.
(Arabic) text is considered the official text in case of any conflicts between the two.
تقديم
هيئة التقييس لدول مجلس التعاون لدول الخليج العربية هيئة إقليمية تضم في عضويتها أجهزة التقييس الوطنية في الدول الأعضاء، ومن مهام الهيئة إعداد المواصفات القياسية واللوائح الفنية الخليجية بواسطة لجان فنية متخصصة.
قرر مجلس الإدارة
لهيئة التقييس لدول مجلس التعاون لدول الخليج العربية
في الاجتماع الـ (10)
بتاريخ 1409/04/16 هـ، الموافق 1988/11/26م اعتماد
ترجمة
الوثيقة
رقم GSO 98:1988
كلائحة فنية خليجية
عنوانها "السيارات
قابلية الأجزاء الداخلية للاشتعال وطرق اختبارها
"
إلى اللغة
الانجليزية
والتي تم دراستها
ضمن برنامج عمل
اللجنة الفنية الخليجية للمواصفات الميكانيكية
(TC02)
.
ويعتبر النص العربي هو المرجع الأساس في حال وجود اختلاف بين النصين.
30mm
20mm
15mm
15mm
10mm
17mm
Gulf Technical RegulationGSO 98:1988
MOTOR VEHICLES- FLAMMABILITY OF
INTERIOR MATERIALS AND THEIR
TESTING METHODS
1SCOPE AND FIELD OF APPLICATION
This standard is concerned with the requirements and methods of testing the resistance to burning, of materials used in the occupant compartments* of motor vehicles.
2COMPLEMENTARY REFERENCES
2.1GSO 42 “ MOTOR VEHICLES - GENERAL REQUIREMENTS”.
2.2GSO 48 “ MOTOR VEHICLESCONFORMITY CERTIFICATES”.
3DEFINITIONS
3.1
Motor vehicle
A vehicle, (exceeding motorcycles), operated by means of a motor, without dependence on rails, or cables or similar guides.
3.2
Burning rate:
The quotient of the burnt distance and the time taken to burn this distance.
3.3
Composite material
A material composed of several layers of similar or different materials intimately held together at their surfaces by methods other than sewing, high-frequency welding or riveting.
3.4
Exposed side
The side of the material, in the occupant compartment, which will face inward when the materials is mounted in the compartment.
*e.g. Seat cushions, seat backs, seat belts, headlining, convertible tops, arm rests, all trim panels including doors, front, rear, and side panels, compartment shelves, head restraint, floor coverings, sun visors, curtains……..