جميع الحقوق محفوظة لهيئة لتقييس لدول مجلس التعاون لدول الخليج العربية. ما لم ينص على خلاف ذلك، لا يجوز إعادة إنتاج أي جزء من هذا المنشور أو استخدامه بأي شكل آخر أو بأي وسيلة، إلكترونية أو ميكانيكية، بما في ذلك التصوير، أو النشر على الإنترنت أو الإنترانت، دون إذن كتابي مسبق من هيئة التقييس لدول مجلس التعاون لدول الخليج العربية على العنوان أدناه أو الدول الأعضاء في الهيئة داخل بلدانهم.
All rights reserved to GCC Standardization Organization (GSO). Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either GSO at the address below or GSO's member body in the country of the requester.
Outreach Dept, Knowledge Management Section
GCC Standardization Organization (GSO)
P.O.Box: 85245 Riyadh 12511
Kingdom of Saudi Arabia
إدارة التواصل، قسم إدارة المعرفة
هيئة التقييس لدول مجلس التعاون لدول الخليج العربية (GSO)
هيئة التقييس لدول مجلس التعاون لدول الخليج العربية هيئة إقليمية تضم في عضويتها أجهزة التقييس الوطنية في الدول الأعضاء ، ومن مهام الهيئة إعداد المواصفات القياسية واللوائح الفنية الخليجية بواسطة لجان فنية متخصصة.
قرر المجلس الفني
لهيئة التقييس لدول مجلس التعاون لدول الخليج العربية
في الاجتماع الـ (56)
بتاريخ 1445/02/24 هـ ،الموافق 2023/09/10م اعتماد
تحديث
المواصفة القياسية الخليجية
رقم GSO ISO 10545-3:2023
وعنوانها "بلاط السيراميك – الجزء3 : تقدير امتصاص الماء والمسامية الظاهرية والكثافة النسبية الظاهرية والكثافة الكلية"
باللغة
الانجليزية
التي تم دراستها
وتبنيها
عن
المنظمة الدولية للتقييس
رقم
ISO 10545-3:2018
بدون إدخال تعديلات فنية عليها
ضمن برنامج عمل
اللجنة الفنية الخليجية لمواصفات التشييد ومواد البناء
(TC06)
المدرجة في خطة المملكة العربية السعودية
.
على أن تلغي وتحل محل
المواصفة القياسية
رقم
GSO ISO 10545-3:2007
.
Gulf Foreword
GCC Standardization Organization (GSO) is a regional organization which consists of the national standardization bodies of GCC member states. One of GSO main functions is to issue gulf standards and technical regulations through specialized technical committees.
GSO Technical Council
in its meeting number (56) held
on 24/02/1445 H,
which corresponds to 10/09/2023, has approved
the update of
Gulf
Standard
GSO ISO 10545-3:2023
titled "Ceramic Tiles — Part 3: Determination of Water Absorption, Apparent Porosity, Apparent Relative Density and Bulk Density" in
English
language
which was studied
and adopted
from
International Organization for Standardization
Standard
ISO 10545-3:2018
without any technical modifications
through
the technical program of
GSO Technical Committee for Construction and Building Materials
(TC06)
in SAUDI ARABIA schedule
.
This document will cancel and replace the Gulf
Standard
GSO ISO 10545-3:2007.
Gulf Standard GSO ISO 10545-3:2023
Gulf Standard GSO ISO 10545-3:2023
Gulf Standard GSO ISO 10545-3:2023
GSO ISO 10545-3:2023 Gulf Standard
International
Standard
ISO10545-3
Ceramic tiles —
Part 3:
Determination of water absorption, apparent porosity, apparent relative density and bulk density
Carreaux et dalles céramiques —
Partie 3: Détermination de l'absorption d'eau, de la porosité ouverte, de la densité relative apparente et de la masse volumique globale
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of the requester.
6.2.3 Tiles greater than 400 cm2 and less than or equal to 3 600 cm2, where x and y >20 cm
6.2.4 Tiles greater than 400 cm2 and less than or equal to 3 600 cm2, where only y is ≤20 cm
6.2.5 Tiles greater than 3 600 cm2
7 Procedure
7.1 Sample preparation
7.2 Impregnation with water
7.3 Suspended weight
8 Expression of results
8.1 Water absorption
8.2 Apparent porosity
8.3 Apparent relative density
8.4 Bulk density
9 Test report
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISO's adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 189, Ceramic tiles.
This second edition cancels and replaces the first edition (ISO 10545-3:1995 which has been technically revised. It also incorporates ISO 10545-3:1995/Cor.1:1997.
The main changes compared to the previous edition are as follows:
—
The impregnation of the samples is now only done by vacuum.
—
The boiling method for impregnation of the samples has been removed.
—
Sampling guidelines according to the dimension of tiles are provided.
A list of all parts in the ISO 10545 series can be found on the ISO website.
Introduction
For ceramic tiles, water absorption is used to classify products. This document outlines the procedures for the measurement of water absorption and related properties using classical Archimedean techniques. Impregnation of the open porosity is achieved by a vacuum method only. Accommodations are provided for large or irregularly shaped ceramic tile.
Gulf Standard GSO ISO 10545-3:2023
Gulf Standard GSO ISO 10545-3:2023
Gulf Standard GSO ISO 10545-3:2023
GSO ISO 10545-3:2023 Gulf Standard
International StandardISO 10545-3:2018(en)
Ceramic tiles —
Part 3:
Determination of water absorption, apparent porosity, apparent relative density and bulk density
1Scope
This document specifies a method for determining water absorption, apparent porosity, apparent relative density and bulk density of ceramic tiles. This method is applicable to classification of tiles and product specifications.
2Normative references
There are no normative references in this document.
3Terms and definitions
No terms and definitions are listed in this document.
ISO and IEC maintain terminological databases for use in standardization at the following addresses: