>>
<<
GSO ISO 17359:2025
GSO - Cover page
Gulf Foreword
ISO - Cover page
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Overview of condition monitoring procedure
5 Cost benefit analysis
6 Equipment audit
 6.1 Identification of equipment
 6.2 Identification of equipment function
7 Reliability and criticality audit
 7.1 Reliability block diagram
 7.2 Equipment criticality
 7.3 Failure modes, effects and criticality analysis
 7.4 Alternative maintenance tasks
8 ​Monitoring method
 8.1 Measurement technique
 8.2 Accuracy of monitored parameters
 8.3 Feasibility of monitoring
 8.4 Operating conditions during monitoring
 8.5 ​Monitoring interval
 8.6 Data acquisition rate
 8.7 Record of monitored parameters
 8.8 Measurement locations
 8.9 Initial alert/alarm criteria
 8.10 Baseline data
9 Data acquisition and analysis
 9.1 Measurement and trending
 9.2 Quality of measurements
 9.3 Measurement comparison to alert/alarm criteria
 9.4 Diagnosis and prognosis
 9.5 Improving diagnosis and/or prognosis confidence
10 Determine maintenance action
11 ​Review
12 Training
Annex A (informative) Examples of condition monitoring parameters
Annex B (informative) Matching fault(s) to measured parameter(s) or technique(s)
Annex C (informative) Typical information to be recorded when monitoring machine types shown in Annex A
Annex D (informative) Overview of condition monitoring standards
Bibliography
30mm
20mm
15mm
15mm
10mm
17mm
Gulf StandardGSO ISO 17359:2025
Gulf StandardGSO ISO 17359:2025
GSO ISO 17359:2025Gulf Standard
GSO ISO 17359:2025
ISO 17359:2018
مواصفة قياسية خليجية
تشخيص ومراقبة حالة الآلات - إرشادات عامة
Gulf Standard
Condition monitoring and diagnostics of machines — General guidelines
ICS:
17.160

هذه الوثيقة محمية بالقانون
COPYRIGHT PROTECTED DOCUMENT
جميع الحقوق محفوظة لهيئة لتقييس لدول مجلس التعاون لدول الخليج العربية.
ما لم ينص على خلاف ذلك، لا يجوز إعادة إنتاج أي جزء من هذا المنشور أو استخدامه بأي شكل آخر أو بأي وسيلة، إلكترونية أو ميكانيكية، بما في ذلك التصوير، أو النشر على الإنترنت أو الإنترانت، دون إذن كتابي مسبق من هيئة التقييس لدول مجلس التعاون لدول الخليج العربية على العنوان أدناه أو الدول الأعضاء في الهيئة داخل بلدانهم.
All rights reserved to GCC Standardization Organization (GSO). Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either GSO at the address below or GSO's member body in the country of the requester.
Outreach Dept, Knowledge Management Section
GCC Standardization Organization (GSO)
P.O.Box: 85245 Riyadh 12511
Kingdom of Saudi Arabia
إدارة التواصل، قسم إدارة المعرفة
هيئة التقييس لدول مجلس التعاون لدول الخليج العربية (GSO)
ص. ب: 85245 الرياض 12511
المملكة العربية السعودية
Tel: +966115208000 :هاتف
Fax: +966115208010 :فاكس
E-Mail: csc@gso.org.sa :بريد إلكتروني
Website: www.gso.org.sa :موقع ويب
30mm
20mm
15mm
15mm
10mm
17mm

Gulf StandardGSO ISO 17359:2025
Gulf StandardGSO ISO 17359:2025
GSO ISO 17359:2025Gulf Standard

Gulf Foreword

GCC Standardization Organization (GSO) is a regional organization which consists of the national standardization bodies of GCC member states. One of GSO main functions is to issue gulf standards and technical regulations through specialized technical committees.
GSO Technical Council in its meeting number (60) held on 23/10/1446 H, which corresponds to 22/04/2025, has approved the update of Gulf Standard GSO ISO 17359:2025 titled "Condition monitoring and diagnostics of machines — General guidelines" in English language which was studied and adopted from International Organization for Standardization Standard ISO 17359:2018 without any technical modifications through the technical program of GSO Technical Committee for Metrology (TC04) in YEMEN schedule . This document will cancel and replace the Gulf Standard GSO ISO 17359:2009.
تقديم خليجي
هيئة التقييس لدول مجلس التعاون لدول الخليج العربية هيئة إقليمية تضم في عضويتها أجهزة التقييس الوطنية في الدول الأعضاء ، ومن مهام الهيئة إعداد المواصفات القياسية واللوائح الفنية الخليجية بواسطة لجان فنية متخصصة.
قرر المجلس الفني لهيئة التقييس لدول مجلس التعاون لدول الخليج العربية في الاجتماع الـ (60) بتاريخ 1446/10/23 هـ ،الموافق 2025/04/22م اعتماد تحديث المواصفة القياسية الخليجية رقم GSO ISO 17359:2025 وعنوانها "تشخيص ومراقبة حالة الآلات - إرشادات عامة" باللغة الانجليزية التي تم دراستها وتبنيها عن المنظمة الدولية للتقييس رقم ISO 17359:2018 بدون إدخال تعديلات فنية عليها ضمن برنامج عمل اللجنة الفنية الخليجية لمواصفات المقاييس (TC04) المدرجة في خطة الجمهورية اليمنية . على أن تلغي وتحل محل المواصفة القياسية رقم GSO ISO 17359:2009 .
30mm
20mm
15mm
15mm
10mm
17mm
Gulf StandardGSO ISO 17359:2025
Gulf StandardGSO ISO 17359:2025
Gulf StandardGSO ISO 17359:2025
GSO ISO 17359:2025Gulf Standard

International

Standard

ISO 17359
Condition monitoring and diagnostics of machines — General guidelines
Surveillance et diagnostic d'état des machines — Lignes directrices générales
Reference number
ISO 17359:2018(en)
Third edition
2018-01
30mm
20mm
15mm
15mm
10mm
17mm
Gulf StandardGSO ISO 17359:2025
Gulf StandardGSO ISO 17359:2025
Gulf StandardGSO ISO 17359:2025
GSO ISO 17359:2025Gulf Standard
30mm
20mm
15mm
15mm
10mm
17mm

Gulf StandardGSO ISO 17359:2025
Gulf StandardGSO ISO 17359:2025
Gulf StandardGSO ISO 17359:2025
GSO ISO 17359:2025Gulf Standard
ContentsPage

Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISO's adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 108, Mechanical vibration, shock and condition monitoring, Subcommittee SC 5, Condition monitoring and diagnostics of machine systems.
This third edition cancels and replaces the second edition (ISO 17359:2011), which has been technically revised.
The following changes have been made:
—
reference to the ISO 55000 family of asset management standards has been included;
—
power transformers have been added to Annex A and Annex B;
—
Annex D has been updated;
—
the Bibliography has been revised.

Introduction

This document provides guidelines for condition monitoring and diagnostics of machines using parameters such as vibration, temperature, tribology, flow rates, contamination, power, and speed typically associated with performance, condition, and quality criteria. The evaluation of machine function and condition may be based on performance, condition or product quality.
Condition monitoring forms a vital component of asset management and this document is the parent document of a group of standards which cover the field of condition monitoring and diagnostics. The range of condition monitoring standards are indispensable for the use and implementation of the ISO 55000 family of asset management standards. This document provides general procedures to be considered when setting up a condition monitoring programme for all types of machine, and includes references to other International Standards and other documents required or useful in this process.
An overview of the current status of condition monitoring International Standards is shown in Annex D.
This document presents an overview of a generic procedure recommended to be used when implementing a condition monitoring programme, and provides further detail on the key steps to be followed. It introduces the concept of directing condition monitoring activities towards identifying and detecting symptoms of root cause failure modes and describes the generic approach to setting alarm criteria, carrying out diagnosis and prognosis, and improving the confidence in diagnosis and prognosis, which are developed further in other International Standards.
Particular techniques of condition monitoring are only introduced briefly and are covered in more detail in other International Standards referenced in the Bibliography.
30mm
20mm
15mm
15mm
10mm
17mm

Gulf StandardGSO ISO 17359:2025
Gulf StandardGSO ISO 17359:2025
Gulf StandardGSO ISO 17359:2025
GSO ISO 17359:2025Gulf Standard
International StandardISO 17359:2018(en)
Condition monitoring and diagnostics of machines — General guidelines

1Scope

This document gives guidelines for the general procedures to be considered when setting up a condition monitoring programme for machines and includes references to associated standards required in this process. This document is applicable to all machines.

2Normative references

The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 2041, Mechanical vibration, shock and condition monitoring — Vocabulary
ISO 13372, Condition monitoring and diagnostics of machines — Vocabulary
ISO 13379-1, Condition monitoring and diagnostics of machines — Data interpretation and diagnostics techniques — Part 1: General guidelines

3Terms and definitions

For the purposes of this document, the terms and definitions given in ISO 2041, ISO 13372 and the following apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
—
ISO Online browsing platform: available at https://www.iso.org/obp
—
IEC Electropedia: available at http://www.electropedia.org/
3.1
equipment
machine or group of machines including all machine or process control components
30mm
20mm
15mm
15mm
10mm
17mm

Gulf StandardGSO ISO 17359:2025
Gulf StandardGSO ISO 17359:2025
Gulf StandardGSO ISO 17359:2025
GSO ISO 17359:2025Gulf Standard
Bibliography
[1]
ISO 1217, Displacement compressors — Acceptance tests
[2]
ISO 2314, Gas turbines — Acceptance tests
[3]
ISO/IEC 2382-14, Information technology — Vocabulary — Part 14: Reliability, maintainability and availability
[4]
ISO 3046-1, Reciprocating internal combustion engines — Performance — Part 1: Declarations of power, fuel and lubricating oil consumptions, and test methods — Additional requirements for engines for general use
[5]
ISO 3046-3, Reciprocating internal combustion engines — Performance — Part 3: Test measurements
[6]
ISO 5151, Non-ducted air conditioners and heat pumps — Testing and rating for performance
[7]
ISO 5389, Turbocompressors — Performance test code
[8]
ISO 5801, Fans — Performance testing using standardized airways
[9]
ISO 6954, Mechanical vibration — Guidelines for the measurement, reporting and evaluation of vibration with regard to habitability on passenger and merchant ships
[10]
ISO 7919 (all parts), Mechanical vibration — Evaluation of machine vibration by measurements on rotating shafts
[11]
ISO 8528-1, Reciprocating internal combustion engine driven alternating current generating sets — Part 1: Application, ratings and performance
[12]
ISO 8528-6, Reciprocating internal combustion engine driven alternating current generating sets — Part 6: Test methods
[13]
ISO 8528-9, Reciprocating internal combustion engine driven alternating current generating sets — Part 9: Measurement and evaluation of mechanical vibrations
[14]
ISO 9906, Rotodynamic pumps — Hydraulic performance acceptance tests — Grades 1, 2 and 3
[15]
ISO 10055, Mechanical vibration — Vibration testing requirements for shipboard equipment and machinery components
[16]
ISO 10816 (all parts), Mechanical vibration — Evaluation of machine vibration by measurements on non-rotating parts
[17]
ISO 13373-1, Condition monitoring and diagnostics of machines — Vibration condition monitoring — Part 1: General procedures
[18]
ISO 13381-1, Condition monitoring and diagnostics of machines — Prognostics — Part 1: General guidelines
[19]
ISO 13350, Industrial fans — Performance testing of jet fans
[20]
ISO 14694, Industrial fans — Specifications for balance quality and vibration levels
[21]
ISO 14695, Industrial fans — Method of measurement of fan vibration
[22]
ISO 14830-1:—2, Condition monitoring and diagnostics of machines — Tribology-based monitoring and diagnostics — Part 1: General guidelines
[23]
ISO 20816 (all parts), Mechanical vibration — Measurement and evaluation of machine vibration
[24]
ISO 55000, Asset management — Overview, principles and terminology
[25]
ISO 55001, Asset management — Management systems — Requirements
[26]
ISO 55002, Asset management — Management systems — Guidelines for the application of ISO 55001
[27]
IEC 60034-1, Rotating electrical machines — Part 1: Ratings and performance
[28]
IEC 60300-3-1, Dependability management — Part 3-1: Application guide — Analysis techniques for dependability — Guide on methodology
[29]
IEC 60300-3-2, Dependability management — Part 3-2: Application guide — Collection of dependability data from the field
[30]
IEC 60300-3-3, Dependability management — Part 3-3: Application guide — Life cycle costing
[31]
IEC 60300-3-11, Dependability management — Part 3-11: Application guide — Reliability centred maintenance
[32]
IEC 60812, Analysis techniques for system reliability — Procedure for failure mode and effects analysis (FMEA)
[33]
IEC 61078, Analysis techniques for dependability — Reliability block diagram and boolean methods
[34]
IEC 61025, Fault tree analysis (FTA)
[35]
ASME Power Test Code PTC 10, Performance Test Code on Compressors and Exhausters
[36]
ASME Power Test Code PTC 22, Performance Test Code on Gas Turbines
[37]
ASME Power Test Code PTC 46, Performance Test Code on Overall Plant Performance
30mm
20mm
15mm
15mm
10mm
17mm
Gulf StandardGSO ISO 17359:2025
Gulf StandardGSO ISO 17359:2025
Gulf StandardGSO ISO 17359:2025
GSO ISO 17359:2025Gulf Standard
ICS 17.160
Price based on 29 pages
iso.org

2 Under preparation.