ICS: |
43.040.60
;
81.040.30
|
|
هذه الوثيقة محمية بالقانون
COPYRIGHT PROTECTED DOCUMENT
|
|||||
|
جميع الحقوق محفوظة لهيئة لتقييس لدول مجلس التعاون لدول الخليج العربية. ما لم ينص على خلاف ذلك، لا يجوز إعادة إنتاج أي جزء من هذا المنشور أو استخدامه بأي شكل آخر أو بأي وسيلة، إلكترونية أو ميكانيكية، بما في ذلك التصوير، أو النشر على الإنترنت أو الإنترانت، دون إذن كتابي مسبق من هيئة التقييس لدول مجلس التعاون لدول الخليج العربية على العنوان أدناه أو الدول الأعضاء في الهيئة داخل بلدانهم.
|
|||||
|
All rights reserved to GCC Standardization Organization (GSO). Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either GSO at the address below or GSO's member body in the country of the requester.
|
|||||
|
Outreach Dept, Knowledge Management Section
GCC Standardization Organization (GSO)
P.O.Box: 85245 Riyadh 12511
Kingdom of Saudi Arabia
|
إدارة التواصل، قسم إدارة المعرفة
هيئة التقييس لدول مجلس التعاون لدول الخليج العربية (GSO)
ص. ب: 85245 الرياض 12511
المملكة العربية السعودية
|
||||
|
Tel:
|
+966115208000
|
هاتف:
|
|||
|
Fax:
|
+966115208010
|
فاكس:
|
|||
|
E-Mail:
|
بريد إلكتروني:
|
||||
|
Website:
|
موقع ويب:
|
||||
هيئة التقييس لدول مجلس التعاون لدول الخليج العربية هيئة إقليمية تضم في عضويتها أجهزة التقييس الوطنية في الدول الأعضاء ، ومن مهام الهيئة إعداد المواصفات القياسية واللوائح الفنية الخليجية بواسطة لجان فنية متخصصة.
قرر المجلس الفني لهيئة التقييس لدول مجلس التعاون لدول الخليج العربية في الاجتماع رقم (14) الذي عقد بتاريخ 1429/02/09هـ ،الموافق 2008/09/03م اعتماد تحديث المواصفة القياسية الخليجية رقم GSO ISO 3537:2008 وعنوانها "السيارات – مواد زجاج الأمان – طرق الاختبارات الميكانيكية " باللغة الانجليزية التي تم دراستها وتبنيها عن المنظمة الدولية للتقييس رقم ISO 3537:1999 بدون إدخال تعديلات فنية عليها ضمن برنامج عمل اللجنة الفنية الخليجية للمواصفات الميكانيكية (TC02) المدرجة في خطة دولة قطر . على أن تلغي وتحل محل المواصفة القياسية رقم GSO ISO 3537:1998 .
GCC Standardization Organization (GSO) is a regional organization which consists of the national standardization bodies of GCC member states. One of GSO main functions is to issue gulf standards and technical regulations through specialized technical committees.
GSO Technical Council in its meeting number (14) held on 09/02/1429 H , which corresponds to 03/09/2008 has approved the update of gulf standard No GSO ISO 3537:2008 titled "Road Vehicles – Safety Glazing Materials – Mechanical Test" in English language which was studied and adopted from International Organization for Standardization Standard ISO 3537:1999 without any technical modifications through the technical program of GSO Technical Committee for Mechanical Products (TC02) in QATAR schedule . This document will cancel and replace the gulf standard GSO ISO 3537:1998 .
INTERNATIONAL STANDARD | ISO 3537 Third edition 1999-03-25 | ||
Road vehicles — Safety glazing materials — Mechanical tests Véhicules routiers — Vitrages de sécurité — Essais mécaniques | |||
| |||||
© ISO 1999 — All rights reserved., Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISO's member body in the country of the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.ch
Web www.iso.ch
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
International Standard ISO 3537 was prepared by Technical Committee ISO/TC 22, Road vehicles, Subcommittee SC 11, Safety glazing materials.
This third edition cancels and replaces the second edition (ISO 3537:1993), which has been technically revised.
This International Standard specifies mechanical test methods relating to the safety requirements for all safety glazing materials in a road vehicle, whatever the type of glass or other material of which they are composed.
The following normative documents contain provisions which, through reference in this text, constitute provisions of this International Standard. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain registers of currently valid International Standards.
For the purposes of this International Standard, the terms and definitions given in ISO 3536 apply.