>>
<<
ISO 24232:2024(en)
ISO - Cover page
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Performance assessment and requirements
 4.1 General requirements and innocuousness
  4.1.1 General requirements
  4.1.2 Innocuousness
 4.2 Water penetration resistance, Wp
 4.3 Water vapour resistance, Ret
 4.4 Tensile strength of the woven outer shell material
 4.5 Tear resistance of the woven outer shell material
 4.6 Bursting strength of the knitted outer shell material
 4.7 Dimensional change of the materials
 4.8 Seam strength of the outer shell material
 4.9 Waterproofness of a readymade garment (optional)
5 Test methods
 5.1 Sampling principles
 5.2 Testing related to general requirements and innocuousness
  5.2.1 Testing related to general requirements
  5.2.2 Innocuousness
 5.3 Pretreatment
  5.3.1 General
  5.3.2 Pretreatment by cleaning
  5.3.3 Pretreatment by abrasion
  5.3.4 Pretreatment by repeated flexing
  5.3.5 Pretreatment with fuel and oil
 5.4 Water penetration resistance, Wp
 5.5 Water vapour resistance, Ret
 5.6 Tensile strength
 5.7 Tear resistance
 5.8 Bursting strength
 5.9 Dimensional change after cleaning
 5.10 Testing of seam strength
 5.11 Testing the waterproofness of a readymade garment (optional)
6 Size designation
7 Marking and care labelling
8 Information supplied by the manufacturer
Annex A (informative) Recommendations for wearing time
Annex B (informative) Test device for one sided exposure to fuel and oil
Bibliography
30mm
20mm
15mm
15mm
10mm
17mm

International

Standard

ISO 24232
Protective clothing — Protection against rain
Habillement de protection — Protection contre la pluie
Reference number
ISO 24232:2024(en)
First edition
2024-10
30mm
20mm
15mm
15mm
10mm
17mm
30mm
20mm
15mm
15mm
10mm
17mm

ContentsPage

Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types of ISO document should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a) patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a) patent(s) which may be required to implement this document. However, implementers are cautioned that this may not represent the latest information, which may be obtained from the patent database available at www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISO's adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 94, Personal safety — Personal protective equipment, Subcommittee SC 13, Protective clothing, in collaboration with the European Committee for Standardization (CEN) Technical Committee CEN/TC 162, Protective clothing including hand and arm protection and lifejackets, in accordance with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement).
Any feedback or questions on this document should be directed to the user’s national standards body. A complete listing of these bodies can be found at www.iso.org/members.html.

Introduction

In this document the measured properties of materials and seams of protective garments and their subsequent classification are intended to ensure an adequate protection level. Water proofness and water vapour resistance are the essential properties tested and marked on the label.
Water proofness is the most important property and it is measured on material of the outer garment layer. Tests are made on pretreated fabric samples and on parts with seams. A test method for an optional readymade garment test after cleaning is described (rain tower test).
Some waterproof materials are impermeable to water vapour transmission. However other materials on the market combine water proofness with water vapour permeability. This property expressed by low water vapour resistance enhances sweat evaporation and significantly contribute to body cooling. This is valuable, because it contributes to better comfort and less physiological strain and prolongs the wearing time in certain climatic conditions (see Annex A).
30mm
20mm
15mm
15mm
10mm
17mm

International StandardISO 24232:2024(en)
Protective clothing — Protection against rain

1Scope

This document specifies requirements and test methods for the performance of materials and readymade garments for protection against the effects of precipitation (e.g. rain, snowflakes), fog and ground humidity. Garments for protection against other effects than precipitation (e.g. water splashes, waves) are excluded from this document.
The protective effects and requirements of footwear, gloves and separate headwear are excluded from the scope of this document.

2Normative references

The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 811:2018, Textiles — Determination of resistance to water penetration — Hydrostatic pressure test
ISO 1421:2016, Rubber- or plastics-coated fabrics — Determination of tensile strength and elongation at break
ISO 1817:2024, Rubber, vulcanized or thermoplastic — Determination of the effect of liquids
ISO 4674-1:2016, Rubber- or plastics-coated fabrics — Determination of tear resistance — Part 1: Constant rate of tear methods
ISO 7854:1995, Rubber- or plastics-coated fabrics — Determination of resistance to damage by flexing
ISO 11092:2014, Textiles — Physiological effects — Measurement of thermal and water-vapour resistance under steady-state conditions (sweating guarded-hotplate test)
ISO 12947-1:1998, Textiles — Determination of the abrasion resistance of fabrics by the Martindale method — Part 1: Martindale abrasion testing apparatus
ISO 12947-2:2016, Textiles — Determination of the abrasion resistance of fabrics by the Martindale method — Part 2: Determination of specimen breakdown
ISO 13688:2013, Protective clothing — General requirements
ISO 13688:2013/Amd.1:2021, Protective clothing — General requirements — Amendment 1
ISO 13934-1:2013, Textiles — Tensile properties of fabrics — Part 1: Determination of maximum force and elongation at maximum force using the strip method
ISO 13935-2:2014, Textiles — Seam tensile properties of fabrics and made-up textile articles — Part 2: Determination of maximum force to seam rupture using the grab method
ISO 13938-1:2019, Textiles — Bursting properties of fabrics — Part 1: Hydraulic method for determination of bursting strength and bursting distension
ISO 13938-2:2019, Textiles — Bursting properties of fabrics — Part 2: Pneumatic method for determination of bursting strength and bursting distension
ISO 23388:2018, Protective gloves against mechanical risks
ISO 24231:2024, Protective clothing — Protection against rain — Test method for ready-made garments against high energy droplets from above
EN 530:2010, Abrasion resistance of protective clothing material — Test methods

3Terms and definitions

For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
—
ISO Online browsing platform: available at https://www.iso.org/obp
—
IEC Electropedia: available at https://www.electropedia.org/
3.1
water vapour resistance
Ret
water-vapour pressure difference between the two faces of a material divided by the resultant evaporative heat flux per unit area in the direction of the gradient
Note 1 to entry: It is a quantity specific to textile materials or composites, which determines the “latent” evaporative heat flux across a given area in response to a steady applied water-vapour pressure gradient. The evaporative heat flux can consist of both diffusive and convective components.
Note 2 to entry: The water-vapour resistance is expressed in square metres pascal per watt.
[SOURCE: ISO 11092:2014, 2.2]
3.2
water penetration resistance
Wp
property of a material to support the hydrostatic pressure based on the opposition to the passage of water through the material
[SOURCE: ISO 11610:2023, 4.6.9]
3.3
outer shell material
outermost shell material of which the garment is made
Note 1 to entry: Based on the definition of outer material, ISO 11610:2023, 4.3.27.
3.4
waterproof liner
liner with a waterproof property
3.5
waterproof thermal liner
thermal liner with a waterpoof property
3.6
lining
innermost lining
innermost layer of fabric or other material inserted in a garment which is intended to be nearest to the wearer's body
Note 1 to entry: Where the lining forms part of a quilted assembly, the quilted assembly shall be regarded as the innermost lining
Note 2 to entry: In this document, lining is without waterproof property.
[SOURCE: ISO 11610:2023, 4.3.7, modified — added Note 2 to entry]
30mm
20mm
15mm
15mm
10mm
17mm

Bibliography
[1]
ISO 3175-2, Textiles — Professional care, drycleaning and wetcleaning of fabrics and garments — Part 2: Procedure for testing performance when cleaning and finishing using tetrachloroethene
[2]
ISO 5085-1, Textiles — Determination of thermal resistance — Part 1: Low thermal resistance
[3]
ISO 6330, Textiles — Domestic washing and drying procedures for textile testing
[4]
ISO 7000, Graphical symbols for use on equipment — Registered symbols
[5]
ISO 11610:2023, Protective clothing — Vocabulary
[6]
ISO 15797, Textiles — Industrial washing and finishing procedures for testing of workwear
[7]
ISO 30023, Textiles — Qualification symbols for labelling workwear to be industrially laundered
[8]
EN 342, Protective clothing — Ensembles and garments for protection against cold
[9]
EN 14058, Protective clothing — Garments for protection against cool environments
30mm
20mm
15mm
15mm
10mm
17mm
30mm
20mm
15mm
15mm
10mm
17mm
ICS 13.340.10
Price based on 12 pages
iso.org