>>
<<
ISO 5667-27:2025(en)
ISO - Cover page
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Principles and general considerations
 4.1 Methodologies
  4.1.1 General
  4.1.2 Grab sampling
  4.1.3 Volume-reduced sampling
 4.2 Selecting the most appropriate sampling method
 4.3 Sampling volume
 4.4 Quality control
  4.4.1 General
  4.4.2 Sources of sampling errors
  4.4.3 Blanks
 4.5 Sampling plan
  4.5.1 General
  4.5.2 Sampling points
  4.5.3 Sampling frequency, duration and timing
5 Reagents
6 Apparatus
 6.1 Grab sampling method
 6.2 Cascade filtration methods
 6.3 Net sampling
7 Sample handling
 7.1 General
 7.2 Grab sampling method
 7.3 Cascade filtration methods
 7.4 Net sampling
8 Procedures
 8.1 Grab sampling method
 8.2 Cascade filtration method 1: Sampling of domestic water, treated wastewater and water samples with low suspended solid content
 8.3 Cascade filtration method 2: Sampling of untreated wastewater or water samples with medium or high suspended solid content
 8.4 Net sampling
9 Sampling report
Bibliography
30mm
20mm
15mm
15mm
10mm
17mm

International

Standard

ISO 5667-27
Water quality — Sampling
Part 27:
Guidance on sampling for microplastics in water
Qualité de l'eau — Échantillonnage —
Partie 27: Recommandations pour l'échantillonnage des microplastiques dans l'eau
Reference number
ISO 5667-27:2025(en)
First edition
2025-03
30mm
20mm
15mm
15mm
10mm
17mm
30mm
20mm
15mm
15mm
10mm
17mm

ContentsPage

Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types of ISO document should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a) patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a) patent(s) which may be required to implement this document. However, implementers are cautioned that this may not represent the latest information, which may be obtained from the patent database available at www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISO's adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 147 Water quality, Subcommittee SC 6, Sampling (general methods).
A list of all parts in the ISO 5667 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A complete listing of these bodies can be found at www.iso.org/members.html.

Introduction

Microplastic occurrence in the environment is a prominent concern both to the public and to the scientific community. Determining the amount and distribution of microplastics in water bodies and domestic water is therefore a critical task.[1]-[6] However, the methodology for sampling microplastics in water samples is still lacking in precision. Consistent methodology is only starting to emerge, but still no universal protocol exists for the sampling of these contaminants in water.
The presence of small plastic fragments in the ocean was first reported in 1972,[7] but it was in 2004 that the term “microplastics” was proposed for the first time to describe plastic particles of a few micrometres in diameter.[8] Since then, a wealth of information became available on the abundance and type of microplastics in the marine environment, freshwater and estuarine systems. However, the different studies have used diverse techniques to sample, extract, treat and detect microplastic present in water.
There are many reasons why different studies investigating microplastic occurrence in water and wastewater show different results. The disparity between some of the findings (for microplastic type and abundance) can be partially explained by the fact that differing sampling techniques have been used. Variables pertaining to both time of year and time of day, flow rate and volume of water sampled, grab sampling or sieving the water over an extended period, the use of plastic containers or tubing, selection of a few parts of the sample for analysis, or dissimilar devices to capture the microplastic fragments, can be the causes of variation in study results.
While several standards for water sampling and water quality already exist (e.g. ISO 5667 series and, in particular, ISO 5667-17), microplastics as particular determinands pose a specific challenge which requires a more specific approach. For example, microplastics sampling requires the use of very specific materials for collecting, handling and storing to avoid cross-contamination. Also, microplastic buoyancy can vary depending on their composition, size, shape or colonization by microorganisms, and microplastics are not homogeneously distributed in the water column. Therefore, a more targeted and detailed set of sampling protocols is required to account for these differences. To better understand the fate and impact of microplastics in the environment, a more specific standardized sampling approach should be adopted and applied.
30mm
20mm
15mm
15mm
10mm
17mm

International StandardISO 5667-27:2025(en)
Water quality — Sampling
Part 27:
Guidance on sampling for microplastics in water
WARNINGPersons using this document should be familiar with normal laboratory practice. This document does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user to establish appropriate safety and health practices and to ensure compliance with any national regulatory conditions.
IMPORTANTIt is essential that tests conducted according to this document be carried out by suitably trained staff.

1Scope

This document specifies the basic methods for sampling suspended microplastics in water (domestic water, freshwater, seawater, treated wastewater and untreated wastewater), for their subsequent characterization. Suspended particles can also include synthetic or semi-synthetic polymeric materials (such as rubber). This document does not cover chemical analysis, biological (ecotoxicological) methods or physical methods, nor the pre-treatment or digestion methods intrinsic to such analyses.
This document covers general methodologies:
—
for grab sampling, sampling using a set of successive filters of different pore sizes (cascade filtration), for water samples with low, medium and high content of suspended solids, and
—
for net sampling using, for example, manta, plankton or neuston nets.

2Normative references

The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 5667-3, Water quality — Sampling — Part 3: Preservation and handling of water samples

3Terms and definitions

For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
—
ISO Online browsing platform: available at https://www.iso.org/obp
—
IEC Electropedia: available at https://www.electropedia.org/
3.1
microplastic
solid plastic or synthetic polymer particle insoluble in water with the largest dimension between 1 μm and 5 mm
Note 1 to entry: Microplastics can show various shapes.
Note 2 to entry: This definition encompasses the ISO/TR 21960 definitions of large microplastics and microplastics.
3.2
plastic
material which contains as an essential ingredient a high polymer and which, at some stage in its processing into finished products, can be shaped by flow
[SOURCE: ISO 472:2013, 2.702, modified — Notes 1 and 2 to entry have been deleted.]
3.3
rubber
family of polymeric materials which are flexible and elastic
[SOURCE: ISO 1382:2020, 3.420, modified — the domain and Notes 1 and 2 to entry have been deleted.]
3.4
suspended solid
solid remaining in suspension in water, which can be removed by sedimentation, filtration or centrifugation
[SOURCE: ISO 6107:2021, 3.554]
3.4.1
high suspended solid content
concentration of solids suspended in water above 500 mg/l
3.4.2
medium suspended solid content
concentration of solids suspended in water ranges between 100 mg/l to 500 mg/l
3.4.3
low suspended solid content
concentration of solids suspended in water ranges between 1 mg/l to 100 mg/l
3.5
grab sample
single discrete sample directly collected from a water body at a specific time and location (and depth when relevant)
3.6
blank
sample identical to the sample of interest, but in the absence of the determinand
3.7
field blank
blank (3.6) to verify possible contamination during sampling
Note 1 to entry: A field blank is prepared in the laboratory using water (filtered before use through an inert filter with a pore size smaller than 1 μm) and sent with the sampling personnel for exposure to the sampling environment.
3.8
domestic water
water either in its original state or after treatment
Note 1 to entry: Domestic water is intended for human use, such as cooking, food preparation, washing, drinking or other domestic purposes.
3.9
limit of detection
smallest true value of the measurand which ensures a specified probability of being detectable by the measurement procedure
Note 1 to entry: For microplastics (3.1), the limit of detection is defined as the methods’ capability of reliably detecting at least one particle or a defined mass.
[SOURCE: ISO/TR 22930-1:2020, 3.6, modified — the term has been changed from "detection limit" to "limit of detection", Note 1 to entry has been replaced and Note 2 to entry has been deleted.]
30mm
20mm
15mm
15mm
10mm
17mm

Bibliography
[1]
United Nations Environment Programme - UNEP (2020). Monitoring Plastics in Rivers and Lakes: Guidelines for the Harmonization of Methodologies. ISBN 978‑92‑807-3819-3. Nairobi.
[2]
GESAMP (2019). Guidelines for the monitoring and assessment of plastic litter and microplastics in the ocean (eds Kershaw P.J., Turra A. and Galgani F.), London, UK, GESAMP Joint Group of Experts on the Scientific Aspects of Marine Environmental Protection, 130pp. (GESAMP Reports and Studies, No. 99).
[3]
HELCOM guidelines on monitoring of microlitter in the water column in the Baltic Sea. HELCOM (2022).
[4]
Braun U. et al. Microplastics Analytics Sampling, Preparation and Detection Methods, in Discussion Paper, BMBF Research Focus “Plastics in the Environment”. 2018.
[5]
Cole, M., et al., Microplastics as contaminants in the marine environment: A review. Marine Pollution Bulletin, 2011. 62(12): p. 2588-2597.
[6]
Michida, Y., et al., Guidelines for Harmonizing Ocean Surface Microplastic Monitoring Methods. Version 1.1. Tokyo, Japan, Ministry of the Environment Japan, 71pp. June 2020.
[7]
Carpenter, E.J. and K.L. Smith, Plastics on the Sargasso sea surface. Science, 1972. 175(4027): p. 1240-1241.
[8]
Thompson, R.C., et al., Lost at sea: Where is all the plastic? Science, 2004. 304(5672): p. 838-838.
[9]
Campanale, C., et al., A Practical Overview of Methodologies for Sampling and Analysis of Microplastics in Riverine Environments. Sustainability, 2020. 12(17): p. 6755.
[10]
ASTM D8332-20, Standard Practice for Collection of Water Samples with High, Medium, or Low Suspended Solids for Identification and Quantification of Microplastic Particles and Fibers5
[11]
Tokai, T., et al., Mesh selectivity of neuston nets for microplastics. Marine Pollution Bulletin, 2021. 165: p. 112111.
[12]
Erni-Cassola, G., R. Dolf, and P. Burkhardt-Holm, Microplastics in the Water Column of the Rhine River Near Basel: 22 Months of Sampling. Environmental Science & Technology, 2024. 58(12): p. 5491-5499.
[13]
Harhash, M., et al., Efficiency of five samplers to trap suspended particulate matter and microplastic particles of different sizes. Chemosphere, 2023. 338: p. 139479.
[14]
Hildebrandt, L., et al., Evaluation of continuous flow centrifugation as an alternative technique to sample microplastic from water bodies. Marine Environmental Research, 2019. 151: p. 104768.
[15]
Hildebrandt, L., et al., Comparison and uncertainty evaluation of two centrifugal separators for microplastic sampling. Journal of Hazardous Materials, 2021. 414: p. 125482.
[16]
Kittner, M., et al., Microplastics in the Danube River Basin: A First Comprehensive Screening with a Harmonized Analytical Approach. ACS ES&T Water, 2022. 2(7): p. 1174-1181.
[17]
Ministry of the Environment Japan (MOEJ) (2021) Guidelines for River Microplastic Monitoring Methods. Tokyo, Japan.
[18]
Brander, S.M., et al., Sampling and Quality Assurance and Quality Control: A Guide for Scientists Investigating the Occurrence of Microplastics Across Matrices. Applied Spectroscopy, 2020. 74(9): p. 1099-1125.
[19]
Cutroneo, L., et al., Microplastics in seawater: sampling strategies, laboratory methodologies, and identification techniques applied to port environment. Environmental Science and Pollution Research, 2020. 27(9): p. 8938-8952.
[20]
Hidalgo-Ruz, V., et al., Microplastics in the Marine Environment: A Review of the Methods Used for Identification and Quantification. Environmental Science & Technology, 2012. 46(6): p. 3060-3075.
[21]
Bannick, C.G., et al., Development and testing of a fractionated filtration for sampling of microplastics in water. Water Research, 2019. 149: p. 650-658.
[22]
Oßmann, B.E., Microplastics in drinking water? Present state of knowledge and open questions. Current Opinion in Food Science, 2021. 41: p. 44-51.
[23]
Schymanski, D., et al., Analysis of microplastics in drinking water and other clean water samples with micro-Raman and micro-infrared spectroscopy: minimum requirements and best practice guidelines. Analytical and Bioanalytical Chemistry, 2021. 413(24): p. 5969-5994.
[24]
Cabernard, L., et al., Comparison of Raman and Fourier Transform Infrared Spectroscopy for the Quantification of Microplastics in the Aquatic Environment. Environmental Science & Technology, 2018. 52(22): p. 13279-13288.
[25]
Kirstein, I.V., et al., Drinking plastics? – Quantification and qualification of microplastics in drinking water distribution systems by µFTIR and Py-GCMS. Water Research, 2021. 188: p. 116519.
[26]
Koelmans, A.A., et al., Microplastics in freshwaters and drinking water: Critical review and assessment of data quality. Water Research, 2019. 155: p. 410-422.
[27]
Almuhtaram, H. and R.C. Andrews, Sampling Microplastics in Water Matrices: A Need for Standardization. ACS ES&T Water, 2022. 2(8): p. 1276-1278.
[28]
Yuan, C., et al., Assessment of microplastic sampling and extraction methods for drinking waters. Chemosphere, 2022. 286: p. 131881.
[29]
Mintenig, S.M., et al., Low numbers of microplastics detected in drinking water from ground water sources. Science of The Total Environment, 2019. 648: p. 631-635.
[30]
Carr, S.A., J. Liu, and A.G. Tesoro, Transport and fate of microplastic particles in wastewater treatment plants. Water research, 2016. 91: p. 174-182.
[31]
Mintenig, S.M., et al., Identification of microplastic in effluents of waste water treatment plants using focal plane array-based micro-Fourier-transform infrared imaging. Water Research, 2017. 108: p. 365-372.
[32]
Roscher, L., et al., Microplastics in two German wastewater treatment plants: Year-long effluent analysis with FTIR and Py-GC-MS. Science of The Total Environment, 2022. 817: p. 152619.
[33]
Sun, J., et al., Microplastics in wastewater treatment plants: Detection, occurrence and removal. Water Research, 2019. 152: p. 21-37.
[34]
Tagg, A.S., et al., Microplastic Monitoring at Different Stages in a Wastewater Treatment Plant Using Reflectance Micro-FTIR Imaging. Frontiers in Environmental Science, 2020. 8.
[35]
Primpke, S., et al., Comparison of pyrolysis gas chromatography/mass spectrometry and hyperspectral FTIR imaging spectroscopy for the analysis of microplastics. Analytical and Bioanalytical Chemistry, 2020. 412(30): p. 8283-8298.
[36]
Pasquier, G., et al., Manta Net: The Golden Method for Sampling Surface Water Microplastics in Aquatic Environments. Frontiers in Environmental Science, 2022. 10.
[37]
EN 15972:2011, Guidance on quantitative and qualitative investigations of marine phytoplankton
[38]
Lenaker, P.L., et al., Vertical Distribution of Microplastics in the Water Column and Surficial Sediment from the Milwaukee River Basin to Lake Michigan. Environmental Science & Technology, 2019. 53(21): p. 12227-12237.
[39]
Barrows, A.P., et al., Grab vs. neuston tow net: a microplastic sampling performance comparison and possible advances in the field. Analytical methods, 2017. 9(9): p. 1446-1453.
[40]
Kautz, M. Neuston Trawl and Whole Water Samples: A Comparison of Microplastic Sampling Techniques in The Gulf of Maine and Their Application to Citizen-Driven Science. in AGU Fall Meeting Abstracts. 2016.
[41]
Johnson, A.C., et al., Identification and Quantification of Microplastics in Potable Water and Their Sources within Water Treatment Works in England and Wales. Environmental Science & Technology, 2020. 54(19): p. 12326-12334.
[42]
Lurry, D.L. and C.M. Kolbe, Interagency field manual for the collection of water-quality data. 2000: US Department of the Interior, US Geological Survey.
[43]
Lindeque, P.K., et al., Are we underestimating microplastic abundance in the marine environment? A comparison of microplastic capture with nets of different mesh-size. Environmental Pollution, 2020. 265: p. 114721.
[44]
ISO 472:2013, Plastics — Vocabulary
[45]
ISO 1382:2020, Rubber — Vocabulary
[46]
ISO 5667 (all parts), Water quality — Sampling
[47]
ISO 6107:2021, Water quality — Vocabulary
[48]
ISO 14644-1, Cleanrooms and associated controlled environments — Part 1: Classification of air cleanliness by particle concentration
[49]
ISO/TR 21960, Plastics — Environmental aspects — State of knowledge and methodologies
[50]
ISO/TR 22930-1:2020, Evaluating the performance of continuous air monitors — Part 1: Air monitors based on accumulation sampling techniques
30mm
20mm
15mm
15mm
10mm
17mm
30mm
20mm
15mm
15mm
10mm
17mm
ICS 13.060.45
Price based on 28 pages
iso.org